Fire Academic

Fire Standards on FireAcademic

NFPA 1877 Selection Care and Maintenance of Wildland Firefighting Protective Clothing and Equipment

IMPORTANT NOTE: This NFPA document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers appear in all publications containing this document and may be found under the heading “Important Notices and Disclaimers Concerning NFPA Standards. ” They can also be viewed at ivivw.nfpa.org/disclaimers or obtained on request from NFPA.

UPDATES, ALERTS, AND FUTURE EDITIONS: New editions of NFPA codes, standards, recommended practices, and guides (i.e., NFPA Standards) are released on scheduled revision cycles. This edition may be superseded by a later one, or it may be amended outside of its scheduled revision cycle through the issuance of Tenta­tive Interim Amendments (TIAs). An official NFPA Standard at any point in time consists of the current edition of the document, together with all TIAs and Errata in effect. To verify that this document is the current edition or to determine if it has been amended by TIAs or Errata, please consult the National Fire Codes® Subscription Service or the “List of NFPA Codes & Standards” at www.nfpa.org/docinfo. In addition to TIAs and Errata, the document information pages also include the option to sign up for alerts for individual documen ts and to be involved in the development of the next edition.

NOTICE: An asterisk (*) following the number or letter designating a paragraph indicates that explanatory material on the paragraph can be found in Annex A.

A reference in brackets f 1 following a section or paragraph indicates material that has been extracted from another NFPA document. Extracted text may be edited for consistency and style and may include the revision of internal paragraph refer­ences and other references as appropriate. Requests for inter­pretations or revisions of extracted text shall be sent to the technical committee responsible for the source document.

Information on referenced and extracted publications can be found in Chapter 2 and Annex C.

Chapter 1 Administration

1.1 Scope.

  • This standard shall specify the minimum requirements used for selection, care, and maintenance of wildland firefight­ing protective clothing and equipment that are compliant with NFPA 1977, including garments, helmets, gloves, footwear, face/neck shrouds, goggles, chain saw protection, and load- carrying equipment.
  • This standard shall not specify requirements for other organizational programs, such as appropriate use of wildland firefighting protective clothing and equipment for training, for operations, or for infection control, because such programs are under the jurisdiction of other NFPA standards.
  • This standard shall not apply to protective ensembles or protective clothing that are compliant with NFPA 1951, NFPA 1971, NFPA 1991, NFPA 1992, NFPA 1994, and NFPA 1999.
  • This standard shall not be construed as addressing all the safety concerns associated with the use of compliant protec­tive clothing and equipment. It shall be the responsibility of the persons and organizations that use compliant protective clothing and equipment to establish safety and health practices and to determine the applicability of regulatory limitations prior to use.
  • This standard shall not be construed as addressing all the safety concerns, if any, associated with the use of this stand­ard by testing or repair facilities. It shall be the responsibility of the persons and organizations that use this standard to conduct testing of protective clothing and equipment to establish safety and health practices and to determine the applicability of regu­latory limitations prior to using this standard for any designing, manufacturing, and testing.
  • Nothing herein shall restrict any jurisdiction from exceeding these minimum requirements.
  • The purpose of this standard shall be to establish basic criteria for selection, inspection, cleaning, decontamination, repair, storage, and retirement of wildland firefighting protec­tive clothing and equipment.
  • The purpose of this standard shall be to establish a program that uses these criteria to reduce the safety risks and potential health risks associated with poorly maintained, conta­minated, or damaged wildland firefighting protective clothing and equipment.
  • This standard shall apply to wildland firefighting cloth­ing and equipment certified as compliant with NFPA 1977.
  • This standard shall not apply to other organizational programs such as appropriate use of wildland firefighting protective clothing and equipment for training, operations, or infection control, because such programs are under the juris­diction of other NFPA standards.
  • This standard shall not apply to respiratory protective equipment other than where such equipment interfaces with wildland firefighting protective clothing and equipment.
  • The requirements of this standard shall not apply to accessories attached to any element of the wildland firefighting protective clothing and equipment unless specifically addressed herein.
  • In this standard, values for measurement are followed by an equivalent in parentheses, but only the first stated value shall be regarded as the requirement.
  • Values in parentheses shall not be considered as the requirements because these values might not be exact equiva­lents.

Chapter 2 Referenced Publications

2.1 General. The documents or portions thereof listed in this chapter are referenced within this standard and shall be considered part of the requirements of this document.

  • NFPA Publications. National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169-7471.

NFPA 1500™, Standard on Fire Department Occupational Safety, Health, and Wellness Program, 2021 edition.

NFPA 1951, Standard on Protective Ensembles for Technical Rescue Incidents, 2020 edition.

NFPA 1971, Standard on Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting, 2018 edition.

NFPA 1977, Standard on Protective Clothing and Equipment for Wildland Fire Fighting and Urban Interface Fire Fighting, 2022 edition.

NFPA 1991, Standard on Vapor-Protective Ensembles for Hazard­ous Materials Emergencies and CBRN Terrorism Incidents, 2016 edition.

NFPA 1992, Standard on Liquid Splash-Protective Ensembles and Clothing for Hazardous Materials Emergencies, 2018 edition.

NFPA 1994, Standard on Protective Ensembles for First Responders to Hazardous Materials Emergencies and CBRN Terrorism Incidents, 2018 edition.

NFPA 1999, Standard on Protective Clothing and Ensembles for Emergency Medical Operations, 2018 edition.

  • Other Publications.

2.3.1 ISO Publications. International Organization for Stand­ardization, ISO Central Secretariat, BIBC II, Chemin de Blan- donnet 8, CP 401, 1214 Vernier, Geneva, Switzerland.

ISO 17011:2017(E), Conformity assessment — General require­ments for accreditation bodies accrediting conformity assessment bodies, 2004.

ISO 17025, General requirements for the competence of testing and calibration laboratories, 2005.

ISO/IEC 17065, Conformity assessment — Requirements for bodies certifying products, processes and services, 2012.

  • References for Extracts in Mandatory Sections. (Reserved)

Chapter 3 Definitions

  • The definitions contained in this chapter shall apply to the terms used in this standard. Where terms are not defined in this chapter or within another chapter, they shall be defined using their ordinarily accepted meanings within the context in which they are used. Merriam-Webster’s Collegiate Dictionary, 11th edition, shall be the source for the ordinarily accepted meaning.
  • NFPA Official Definitions.

3.2.1* Approved. Acceptable to the authority having jurisdic­tion.

3.2.2* Authority Having Jurisdiction (AHJ). An organization, office, or individual responsible for enforcing the requirements of a code or standard, or for approving equipment, materials, an installation, or a procedure.

3.2.3 Labeled. Equipment or materials to which has been attached a label, symbol, or other identifying mark of an organ­ization that is acceptable to the authority having jurisdiction and concerned with product evaluation, that maintains peri­odic inspection of production of labeled equipment or materi­als, and by whose labeling the manufacturer indicates compliance with appropriate standards or performance in a specified manner.

3.2.4* Listed. Equipment, materials, or services included in a list published by an organization that is acceptable to the authority having jurisdiction and concerned with evaluation of products or services, that maintains periodic inspection of production of listed equipment or materials or periodic evalua­tion of services, and whose listing states that either the equip­ment, material, or service meets appropriate designated standards or has been tested and found suitable for a specified purpose.

  • Indicates a mandatory requirement.
  • Indicates a recommendation or that which is advised but not required.
  • An NFPA Standard, the main text of which contains only mandatory provisions using the word “shall” to indicate requirements and that is in a form generally suitable for mandatory reference by another standard or code or for adoption into law. Nonmandatory provisions are not to be considered a part of the requirements of a standard and shall be located in an appendix, annex, footnote, informational note, or other means as permitted in the NFPA Manuals of Style. When used in a generic sense, such as in the phrase “standards development process” or “standards development activities,” the term “standards” includes all NFPA Standards, including Codes, Standards, Recommended Practices, and Guides.

3.3 General Definitions.

  • An item, or items, that could be attached to a certified product but that are not necessary for the certified product to meet the requirements of the standard.
  • Base-Layer Garment. The first layer of a textile structure that is in direct contact with the skin (e.g., briefs, t-shirts, bras, socks).

 

Biological Terrorism Agents.

Liquid or particulate agents that consist of a biologically derived toxin or pathogen to inflict lethal or incapacitating casualties.

Body Fluids

Fluids that are produced by the body, including but not limited to blood, semen, mucus, feces, urine, vaginal secretions, breast milk, amniotic fluids, cerebrospinal fluid, synovial fluid, and pericardial fluid.

  • Procedures for cleaning, decontamination, and storage of protective clothing and equipment.
  • Certification/Certified. A system whereby a certification organization determines that a manufacturer has demonstrated the ability to produce a product that complies with the require­ments of a specific standard(s), authorizes the manufacturer to use a label on listed products that comply with the require­ments of that standard(s), and establishes a follow-up program conducted by the certification organization as a check on the methods the manufacturer uses to determine continued compliance of labeled and listed products with the require­ments of that standard(s).
  • The formation of a brittle residue when material is exposed to thermal energy.
  • The act of removing soils and contaminants from clothing and equipment by mechanical, chemical, ther­mal, or combined processes.
  • Contamination/Contaminated. The process by which clothing and equipment are exposed to hazardous materials, body fluids, or chemical, biological, radiological, and nuclear (CBRN) terrorism agents.
  • Cross-Contamination. The transfer of contamination from one item to another or to the environment.
  • Crown Straps. The part of the helmet suspension that passes over the head.
  • The act of removing contaminates from protective clothing and equipment by a physical, chemi­cal, or combined process. (See also 3.3.8, Cleaning.)
  • The ability of a material to return to its origi­nal form after being stretched.
  • Field Evaluation. The nonlaboratory assessment of an element.
  • The quality, state, and manner in which clothing and equipment, when worn, relate to the human body.

Flame Resistance (Protective Clothing and Equipment)

The property of a material whereby combustion is prevented, terminated, or inhibited following the application of a flaming or nonflaming source of ignition, with or without subsequent removal of the ignition source.

  • The ability of the clothing and equip­ment or a component to continue to be utilized for its inten­ded purpose.
  • Nonfabric components of the protective clothing and equipment, including but not limited to those made of metal or plastic.
  • Hazardous Materials. Substances (solid, liquid, or gas) that when released are capable of creating harm to people, the environment, and property.
  • Independent Service Provider (ISP). See 3.3.34, Veri­fied Independent Service Provider (ISP).
  • The ability of an element to remain intact and provide continued minimum performance.
  • The inspection, service, and repair of protective clothing and equipment, including the determina­tion for removal from service.
  • Major A Seam. Seam assemblies where rupture exposes the wearer to immediate danger.
  • The entity that directs and controls the compliant product design, compliant product manufacturing, or compliant product quality assurance or the entity that assumes the liability for the compliant product or provides the warranty for the compliant product.
  • Manufacturer-Trained Organization. A nonverified organization trained by an element manufacturer of the same element type to conduct advanced cleaning, advanced inspec­tion, and/or basic repair on the organization’s clothing and equipment.
  • A response to heat by a material resulting in evidence of flowing or dripping.
  • Minor Seam. Remaining seam assemblies that are not classified as major seams.
  • The entity that provides the direct management and supervision for the emergency services personnel.
  • The process of permanently removing an element from emergency operations service in the organiza­tion.
  • The risk assessment process used to deter­mine what protective clothing and equipment (PCE) is neces­sary for protection of fire and emergency services response personnel from an anticipated specific hazard or other activity, the procurement of the appropriate PCE, and the choice of the proper PCX for a specific hazard or activity at an emergency incident.
  • Soiled/Soiling. The accumulation of materials that are not considered hazardous but could degrade the performance of the element.
  • Stress Area. Those areas of the garment that are subjected to more wear, including, but not limited to, crotches, knees, elbows, and shoulders.
  • The energy attenuating system of the helmet that is made up of the headband and crown strap.

Verified Independent Service Provider (ISP)

An inde­pendent service provider verified by a third-party certification organization to conduct cleaning, repair service, or both.

3.3.35* Verified Organization. An organization, verified by a third-party certifier, to conduct cleaning, repair service, or both.

Chapter 4 Program

4.1.1* The organization shall develop and implement a program for the selection, care, and maintenance of wildland firefighting personal protective equipment (PPE) used by the members of the organization in the performance of their assigned functions.

  • This program shall have the goal of providing wildland firefighting PPE that are suitable and appropriate for the inten­ded use; maintaining such protective PPE in a safe, usable condition to provide the intended protection to the user; removing from use such PPE that could cause or contribute to user injury, illness, or death because of its condition; and reconditioning, repairing or retiring such PPE.
  • Where this program for the selection, care, and mainte­nance of wildland firefighting PPE is part of an organization’s overall program on protective clothing and protective equip­ment, the portion of the organization’s overall program that affects wildland firefighting PPE shall be in accordance with Section 4.2.

Program Organization for Wildland Firefighting PPE

4.2.1 The organization shall develop written standard operat­ing procedures (SOP) that shall identify and define the various parts of the program and the various roles and responsibilities of the organization and of the members.

4.2.2 The program shall at least incorporate the requirements within the chapters listed in Table 4.2.2.

4.2.3* The organization shall establish policy regarding base- layer garments that are permitted to be worn under the PPE assigned by the organization.

  • The organization shall establish procedures for evalu­ating base-layer garments to determine whether or not the base-layer garment will affect the performance of the PPE.
  • The organization shall contact the PPE manufacturer for advice and/or data as to what base-layer garment(s) the PPE manufacturer permits to be used with its specific prod­uct (s).
  • The organization shall not permit base-layer garments that would degrade the performance of the PPE.

4.2.4 The organization shall establish a policy regarding acces­sories that are permitted to be attached to the organization’s PPE.

  • The organization shall establish procedures for evalu­ating accessories to determine whether the accessories will affect the performance of the PPE.
  • The organization shall contact the PPE manufacturer for advice and/or data as to what accessories the PPE manufac­turer permits to be used with its specific product(s).

Required Program Parts for Wildland Firefighting PPE

  • The organization shall not add accessories and shall not permit accessories to be added to PPE that would degrade the performance of the PPE.

4.2.5* The organization shall use one of the following to perform cleaning, inspection, and repair services of PPE, as shown in Table 4.2.5:

  • Manufacturer-trained organization for the organization’s PPE only
  • Verified organization
  • Verified independent service provider (ISP)

4.2.5.1 Verified organizations and verified ISPs shall meet the requirements of Chapter 11 and shall be verified by a third- party certification organization.

4.2.5.2* Where an organization is a verified organization or uses a verified ISP, approval from the element manufacturer shall not be required.

4.2.5.3* Verified organizations and verified ISPs shall receive written verification from the third-party certification organiza­tion to conduct garment element advanced cleaning and advanced inspection services or advanced cleaning, advanced inspection, and advanced repair services.

  • Written verification shall indicate that the verified organization or the verified ISP has demonstrated a thorough knowledge of this standard as well as the design and perform­ance requirements of NFPA
  • All garment advanced repairs shall be conducted by the garment manufacturer, a verified organization, or a verified ISP.
  • Manufacturer-trained organizations performing advanced cleaning and advanced inspection shall be trained by an element manufacturer of the same element type or by a veri­fied ISP.
  • The element manufacturer or verified ISP shall provide documentation that the organization has received the necessary training.

4.2.6 The organization shall develop specific criteria for removal of protective clothing and equipment from service, in accordance with Chapter 10. The criteria for retirement shall include, but not be limited to, issues that are specific to the clothing and equipment being used by the organization, the manufacturers’ instructions, and the experience of the organi­zation.

Responsibilities for Garment Element Inspection, Cleaning, and Repair Element Verified  Manufacturer Verified ISP Organization

Manufacturer- Trained Organization End User

  • The organization shall compile and maintain records on their wildland firefighting PPE.
  • At least the following records shall be kept for each PPE:
    • Manufacturer and model name or design
    • Manufacturer’s identification number, lot number, or serial number
    • Month and year of manufacture
  • Manufacturer’s Instructions.
  • When issuing new PPE, the organization shall provide users with the instructions provided by the PPE’s manufacturer on the care, use, and maintenance of the PPE, including any warnings provided by the manufacturer.
  • Unless otherwise specified herein, where the manufac­turer’s instructions regarding the care or maintenance of its PPE differ from a specific requirement in this standard, the manufacturer’s instructions shall be followed for that require­ment.
  • The organization shall retain a copy of manufacturer’s instructions regarding the care, use, and maintenance of their PPE.

Protecting the Public and Personnel from Contamination.

The organization shall develop written SOPs that minimize the public’s exposure to contaminated PPE.

  • The SOPs shall require that contaminated PPE not be worn or stored in the living areas of fire department facilities.
  • The public shall not be exposed at any time, except during emergency operations, to contaminated PPE.
  • Contaminated PPE shall not be brought into the home, washed in home laundries, or washed in public laundries.
  • Reporting Personal Protective Equipment Health and Safety Concerns.
  • The organization shall report all PPE health and safety concerns, if caused by a known or suspected element failure, to the element manufacturer and certification organization.
  • The organization shall notify the manufacturer and the certification organization in writing of such known or suspec­ted element failures.
  • The organization shall request written acknowledgment from the element manufacturer and certification organization within 30 days.

Chapter 5 Selection 5.1 Selection and Purchase.

5.1.1* Prior to starting the selection process of wildland fire- fighting PPE, a risk assessment shall be performed. The risk assessment shall include, but not be limited to, the hazards that wildland firefighters could encounter, based on the following:

  • Type of duties performed
  • Frequency of use of clothing and equipment
  • Organization’s experiences
  • Incident operations
  • Geographic location and climate
  • The organization shall review the current editions of NFPA 1977 and NFPA 1500 and any applicable federal or state OSHA standards, as well as organizational rules and regula­tions, relating to wildland firefighting in order to determine how they affect the selection process.
  • The organization shall confirm that the PPE is certified by a third-party certification organization as being compliant with NFPA
  • Based on the risk assessment, the organization shall compile and evaluate information on the comparative strengths and weaknesses of the items under consideration.
  • The organization shall ensure that the items under consideration interface properly with the other personal protective items with which they will be used.
  • Where a field evaluation is conducted, the organization shall establish criteria to ensure a systematic evaluation.
  • Where the organization develops purchase specifica­tions, at least the following criteria shall be included:
    • Purchase specifications shall require that the items to be purchased are compliant with the current edition of NFPA
    • Where the organization selects criteria that exceed the minimum of NFPA 1977, such criteria shall be stipulated in the purchase specifications.
    • Purchase specifications shall require that manufacturers’ bids include substantiation of certification for each item and model stated in their bids.
    • * Where applicable, the purchase specifications shall define the process for determining proper fit.
    • The organization shall compare each bid submittal against purchase specifications.
  • Upon receipt, organizations shall inspect purchased protective items to ensure they meet the organizations’ specifi­cations and that they were not damaged during shipment. Organizations shall also verify quantity and sizes of the protec­tive items received.
  • Organizations shall examine information supplied with the products such as instructions, warranties, and technical data.
  • Procedures shall be established for returning unsatis­factory products if the organization’s specifications are not met.

5.1.11* The organization’s needs assessment shall be written into a specification of performance and/or design require­ments for the wildland firefighting PPE.

5.1.12* Using the written specifications, the organization shall select a supplier or shall solicit bids from manufacturers or vendors of wildland firefighting PPE.

5.1.13* The organization shall carefully check bid quotation and any supplied samples of the wildland firefighting PPE against the bid specifications.

5.1.14 The organization shall recommend the award of the contract to the selected manufacturer or vendor to the purchasing authority.

5.1.15* Upon delivery of the wildland firefighting PPE purchased, the organization shall inspect the order for completeness against the purchase specifications.

5.1.16 The organization shall periodically review and docu­ment how the wildland firefighting PPE specifications meet the organization’s needs and applicable standards and revise speci­fications as needed for new or replacement equipment.

5.2* Specific Requirements for Wildland Firefighting Protec­tive Garments, Cold Weather Protection, and Face and Neck Shrouds.

5.2.1* Protective Garments. The organization shall ensure that wildland firefighting protective garments and cold weather protection provide limited thermal and physical protection from the hazards associated with wildland firefighting.

  • Cold Weather Protection. The organization shall ensure that wildland firefighting cold weather protection include, but are not limited to, jacket, shirt, trousers, cold weather outer­wear, or one-piece garment which provides thermal and limited physical protection from the hazards associated with wildland firefighting.
  • Face and Neck Shrouds. The organization shall ensure that wildland firefighting face and neck shrouds provide at least minimum thermal protection to the face and neck.
  • The organization shall ensure that wild- land firefighting garments are compatible with gloves and foot­wear in order to provide continuous minimum protection to the upper and lower torsos, the hands, and the feet.

Chapter 6 Inspection

6.1* General.

  • Universal precautions shall be observed, as appropriate, in the handling of clothing and equipment.
  • Items contaminated by hazardous materials or biological agents shall be decontaminated before any additional inspec­tion is initiated.

6.1.3* The organization shall establish guidelines for its members to follow in determining when an item is soiled to the extent that cleaning is necessary.

6.1.4 The organization shall determine appropriate actions to be taken if an item is found to be in need of cleaning, decon­tamination, or repair.

  • As a minimum, any necessary cleaning or decontami­nation shall be done in accordance with the requirements specified in Chapter 7.
  • As a minimum, any necessary repairs shall be made in accordance with the requirements specified in Chapter 8.

6.2 Inspection.

  • Inspections of all issued PPE shall be conducted at the time of issue, after each use, or at a minimum every 12 months by individual members or members who have been trained to perform the inspection.
  • The organization shall establish what constitutes “use” to include at least each time an item is exposed or is suspected of having been exposed to damage or contamination.
  • The inspection shall include, as a minimum, the inspec­tions specified in2.3.1 through 6.2.3.7.
  • Garments and face/neck shrouds shall be inspected for the following:
    • Soiling
    • Contamination from hazardous materials or biological agents
    • Physical damage, such as the following:
      • Rips, tears, and cuts
      • Damaged or missing hardware and closure systems
      • Thermal damage, such as charring, burn holes, and melting
    • Damaged or missing retroreflective trim
  • Helmets shall be inspected for the following:
    • Soiling
    • Contamination from hazardous materials or biological agents
    • Physical damage to the shell, such as the following:
      • Cracks, crazing, dents, and abrasions
      • Thermal damage to the shell, such as bubbling, soft spots, warping, or discoloration
    • Damaged or missing components of the suspension and retention systems
    • Damaged or missing retroreflective trim
  • Gloves shall be inspected for the following:
    • Soiling
    • Contamination from hazardous materials or biological agents
    • Physical damage, such as the following:
      • Rips, tears, and cuts
      • Thermal damage, such as charring, burn holes, and melting
    • Shrinkage
    • Loss of elasticity/flexibility
  • Footwear shall be inspected for the following:
    • Soiling
    • Contamination from hazardous materials or biological agents
    • Physical damage, such as the following:
      • Cuts, tears, and punctures
      • Thermal damage, such as charring, burn holes, and melting
    • Closure system component damage and functionality
  • Goggles shall be inspected for the following:
    • Soiling
    • Contamination from hazardous materials or biological agents
    • Physical damage, such as the following:
      • Damage to the frame
      • Excessive scratching or fogging of the lenses
      • Loss of elasticity and adjustment of headband
      • Thermal damage, such as charring, burn holes, and melting
    • Chain saw leg protectors shall be inspected for the following:
      • Soiling
      • Contamination from hazardous materials or biological agents
      • Physical damage, such as the following:
        • Rips, tears, and cuts
        • Thermal damage, such as charring, burn holes, and melting
      • Shrinkage
      • Loss of flexibility
      • Functionality of all hardware, including buckles, slides, and zippers

6.2.3.7 Load-carrying protective equipment shall be inspected for the following:

  • Soiling
  • Contamination from hazardous materials or biological agents
  • Physical damage, such as the following:
    • Rips, tears, and cuts
    • Thermal damage, such as charring, burn holes, and melting
  • Shrinkage
  • Loss of flexibility
  • Functionality of all hardware, including buckles, slides, and zippers

Chapter 7 Cleaning and Decontamination 7.1* General.

7.1.1* Organizations shall provide a means for having PPE cleaned and decontaminated.

  • Contaminated PPE shall not be brought into the homeor washed in home laundries.
  • The use of public laundries shall be permitted when a procedure to decontaminate the machines after use is estab­lished.
  • Commercial dry cleaning shall not be used as a means of cleaning or decontaminating PPE unless approved by the PPE or element manufacturer.

7.1.5* When a commercial cleaning service or ISP is used, it shall demonstrate to the organization’s satisfaction that proce­dures for cleaning and decontamination do not compromise the performance of PPE.

7.2 Garments.

7.2.1* Cleaning of soiled wildland firefighting PPE shall be done in accordance with manufacturers’ recommendations and instructions.

7.2.2 Contaminated wildland firefighting garments shall be either laundered in washing equipment dedicated solely to that purpose or properly disposed of.

7.2.2.1 The public shall not be exposed at any time to conta­minated garments.

7.2.2.2* PPE shall not be brought into the homeand washed in home laundries.

7.2.2.3 If contaminated protective garments are to be laun­dered, organizations shall provide a washing machine (s) for the sole purpose of cleaning contaminated protective garments or shall contract with an outside service for that purpose.

7.2.2.4* Unless specifically advised otherwise by manufactur­ers’ instructions, the following cautions shall be heeded:

  • Bleach shall not be used.
  • Garments shall be, as a minimum, double rinsed.
  • Water temperature shall not exceed 40°C (105°F).
  • A mild detergent with a pH range of not less than0 pH and not greater than 10.5 pH as indicated on the product safety data sheet (SDS) or original product container shall be used.
  • Garments shall not be exposed to direct sunlight, indirect sunlight, or fluorescent light when air dried.

7.2.3* Organizations shall be permitted to use a contract cleaning service for cleaning of wildland firefighting PPE.

  • Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures that the manufacturer provided with the element. In absence of manufacturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.
  • Helmets shall not be machine cleaned or dried.
  • Helmet shells, headbands, crown straps, and suspension systems shall be cleaned in a utility sink using mild detergent and water.
  • Helmets and suspension systems shall be air dried out of direct sunlight, indirect sunlight, or fluorescent light.
  • The manufacturer shall be consulted if stronger clean­ing agents are required.
  • Do not use solvents.
  • Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures that the manufacturer provided with the element. In absence of manufacturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.
  • Goggles shall not be machine cleaned or dried.

7.4.3* Goggle bodies, attachments, and lenses shall be cleaned using a soft dry cloth.

7.4.4 The manufacturer shall be consulted if stronger clean­ing agents are required.

  • Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures that the manufacturer provided with the element. In absence of manufacturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.
  • Gloves shall not be machine dried with heat.

7.6.1 Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures provided by the manufacturer. In absence of manu­facturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.

  • Footwear shall not be machine cleaned or machine dried.
  • Footwear shall be cleaned in a utility sink using mild detergent (pH range > 6.0 and < 10.5 as indicated on the prod­uct SDS or original product container), water, and a soft bristle brush.
  • The manufacturer shall be consulted if stronger clean­ing agents are required.
  • Footwear shall be air dried in a well-ventilated area, away from direct sunlight, indirect sunlight, or fluorescent light.
  • Face and Neck Shrouds. See Section 7.2 for garment requirements.
  • Wildland Firefighting Load-Carrying Protective Equip­ment.
  • Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures provided by the manufacturer. In absence of manu­facturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.
  • Load-carrying protective equipment shall not be machine washed.
  • Load-carrying protective equipment shall not be machine dried using heat.
  • Wildland Firefighting Chain Saw Leg Protectors.
  • Organizations shall examine the manufacturer’s label and user information for instructions on cleaning and drying procedures provided by the manufacturer. In absence of manu­facturer’s instructions or manufacturer’s approval of alternative procedures, the cleaning and drying procedures provided in this section shall be used.
  • Wildland firefighting chain saw leg protectors shall not be machine cleaned, machine dried, or pressure washed.
  • Wildland firefighting chain saw leg protectors shall be cleaned in a utility sink or soak tank using a citrus-based cleaner (pH range > 6.0 and < 10.5 as indicated on the product SDS or original product container) and a brush, then rinsed thoroughly with clean water.
  • Wildland firefighting chain saw leg protectors shall be air dried in a well-ventilated area, away from direct sunlight, indirect sunlight, and fluorescent light.

7.9.5* If excessive soiling by chain saw fuel and bar oil cannot be decontaminated by normal manufacturer’s instructions, the leg protectors shall be retired.

Chapter 8 Repair

8.1 Garment Repair.

8.1.1 All repairs shall be performed by the original manufac­turer, by a verified ISP who has received training, or by a member(s) of the organization who has received training in the repair of clothing and equipment and is responsible for performing or managing specialized repairs.

  • Garments shall be cleaned before any repair work is undertaken.
  • All repairs and alterations to garments shall be done in a manner approved by the manufacturer and using materials approved by the manufacturer, including, but not limited to, fabric, thread type, stitch construction, hardware, and hard­ware backing.
  • Because there are different methods of construction, the clothing manufacturer shall be contacted if the organization is unsure whether a field repair can be made without adversely affecting the integrity of the garment.
  • Major repairs to the garment shall be accomplished only by the manufacturer or by a manufacturer-recognized repair facility consistent with the manufacturer’s instructions and methods. The manufacturer shall be contacted if the organiza­tion is unsure whether a repair is major or minor or can be accomplished without adversely affecting the integrity of the garment.
  • Repairs shall be completed on all components that have been damaged.
  • Repairs and alterations shall be performed using seam­ing methods consistent with the manufacturer’s instructions. Seaming methods shall include, but not be limited to, seam type, stitches per inch, and manner of construction.

8.1.8* Restitching of more than 1 in. (2.5 cm), continuous, of a major seam either shall require consulting the manufacturer or shall be performed by the manufacturer or by a manufacturer-recognized repair facility in a manner consistent with the manufacturer’s instructions.

  • All minor seams shall be repaired or altered in a manner consistent with the manufacturer’s instructions.
  • All repaired stress areas shall be reinforced in a manner consistent with the manufacturer’s instructions.
  • Repair Criteria.
  • Repairs of minor tears, char marks, ember burns, and abraded areas shall be limited to those where the damaged area can be covered by a maximum of a 50 in.2 (32 cm2) patch.
  • The finished edge of the patch shall extend at least 1 in. (2.5 cm) in all directions beyond the damaged area.
  • To prevent fraying, the patch shall have no raw edges.
  • To prevent further damage, tears, holes, and abra­sions shall be mended prior to the patch being applied.
  • Trim Repair.
  • Replacement trim shall be obtained from the garment manufacturer or the manufacturer’s recognized source and installed in a manner consistent with the garment manufacturer’s method of construction.
  • Trim being replaced shall be completely removed so that no new trim is sewn over older trim.
  • If a repair or alteration necessitates replacing trim, an equal amount of trim shall be installed; no repair or alteration shall result in a reduction of the total amount of trim on the garment.
  • If replacing trim necessitates sewing into a major A seam, trim replacement shall he clone only by the manufac­turer or by a repair facility recognized by the manufacturer.
  • If unsure of the complexity of the repair, the organi­zation shall consult the manufacturer.
  • Replacement hardware shall be installed in a manner consistent with the garment manufacturer’s method of construction.
  • Replacement hardware shall be obtained from the garment manufacturer or the manufacturer’s recognized source.
  • Where hardware is to be replaced, the reinforcement backing material either shall be reinstalled or, if no longer serv­iceable, shall be replaced.
  • If unsure of the complexity of the repair, the organi­zation shall consult the manufacturer.
  • Replacement zippers shall be installed in a manner consistent with the garment manufacturer’s method of construction.
  • Replacement zippers shall be obtained from the manufacturer or the manufacturer’s recognized source.
  • If unsure of the complexity of the repair, the organi­zation shall consult the manufacturer.
  • Replacement Hook and Loops.
  • Replacement hook and loop fastener tape shall be installed in a manner consistent with the garment manufactur­er’s method of construction.
  • Replacement hook and loop shall be obtained from the garment manufacturer or the manufacturer’s recognized source.
  • If unsure of the complexity of the repair, the organi­zation shall consult the manufacturer.
  • Replacement Reinforcement.
  • Replacement reinforcement materials shall be instal­led in a manner consistent with the garment manufacturer’s method of construction.
  • Replacement reinforcement material shall be obtained from the garment manufacturer or the manufactur­er’s recognized source.
  • If unsure of the complexity of the repair, the organi­zation shall consult the manufacturer.

8.2 Helmet Repair.

  • All repairs shall be performed by the original manufac­turer, by a verified ISP who has received training, or by a member(s) of the organization who has received training in the repair of helmets and is responsible for performing or managing specialized repairs.
  • Helmets shall be cleaned before any repair work is undertaken.
  • Where replacement of a helmet component is performed, the replacement component(s) shall be obtained from the helmet manufacturer or the manufacturer’s recog­nized source.
  • If there is indication of a crack, dent, abrasion, bubbling, soft spot, discoloration, or warping in the helmet shell, the shell shall be replaced (see Section 10.1).
  • Small surface nicks and scratches shall be repaired in accordance with the manufacturer’s instructions.
  • Goggle Repair.
  • All repairs shall be performed by the original manufac­turer, by a verified ISP who lias received training, or by a member(s) of the organization who has received training in the repair of goggles and is responsible for performing or managing specialized repairs.
  • Goggles shall be cleaned before any repair work is undertaken.
  • Where replacement of a goggle component is performed, the replacement component(s) shall be obtained from the goggles manufacturer or the manufacturer’s recog­nized source.
  • If there is indication of a crack, dent, abrasion, bubbling, soft spot, discoloration, or warping in the goggle, the goggle shall be replaced (see Section 10.1).
  • Small surface nicks and scratches in the goggle frame or body shall be repaired in accordance with the manufacturer’s instructions.
  • Glove Repair.
  • All repairs shall be performed by the original manufac­turer, by a verified ISP who lias received training, or by a member(s) of the organization who has received training in the repair of gloves and is responsible for performing or managing specialized repairs.
  • Gloves shall be cleaned before any repair work is under­taken.
  • All repairs to gloves shall be done in a manner approved by the manufacturer and using materials approved by the manufacturer.
  • Footwear Repair.
  • All repairs shall be performed by the original manufac­turer, by a verified ISP who lias received training, or by a member(s) of the organization who has received training in the repair of footwear and is responsible for performing or managing specialized repairs.
  • Footwear shall be cleaned before any repair work is undertaken.
  • All repairs to leather boots other than the replacement of boot laces, insoles, and zipper assemblies shall be performed by the manufacturer or a repair service recognized by the manufacturer.
  • Face/Neck Shroud Repair.

8.6.1 All repairs shall be performed by the original manufac­turer, by a verified ISP who lias received training, or by a member(s) of the organization who has received training in the repair of face/neck shroud and is responsible for perform­ing or managing specialized repairs.

  • Face/neck shrouds shall be cleaned before any repair work is undertaken.
  • All repairs to face/neck shrouds shall be done in a manner approved by the manufacturer and using materials approved by the manufacturer.
  • Chain Saw Leg Protector Repair.
  • All repairs shall be performed by the original manufac­turer, by a verified ISP who has received training, or by a member(s) of the organization who has received training in the repair of chain saw leg protectors and is responsible for performing or managing specialized repairs.
  • Chain saw leg protectors shall be cleaned before any repair work is undertaken.
  • All repairs to chain saw leg protectors shall be done in a manner approved by the manufacturer and using materials approved by the manufacturer.
  • Load-Carrying Protective Equipment.
  • All repairs shall be performed by the original manufac­turer, by a verified ISP who has received training, or a by member(s) of the organization who has received training in the repair of load-carrying protective equipment and is respon­sible for performing or managing specialized repairs.
  • Load-carrying protective equipment shall be cleaned before any repair work is undertaken.
  • All repairs to load-carrying protective equipment shall be done in a manner approved by the manufacturer and using materials approved by the manufacturer.

Chapter 9 Storage

9.1 Requirements for All PPE.

  • PPE shall not be stored in or exposed to direct sunlight, indirect sunlight, or fluorescent light while not being worn.
  • PPE shall be clean and dry before storage.
  • PPE storage areas shall be clean, dry, and well ventilated.
  • PPE shall not be stored in airtight containers unless they are new and unissued.
  • PPE shall not be stored at temperatures below -32°C (-25T) or above 82°C (180°F).
  • PPE shall not be stored or transported in compartments or trunks with sharp objects, tools, or other equipment that could damage the clothing and equipment unless the items are in a protective case or bag to prevent damage.
  • PPE shall not be stored in contact with hydraulic fluids, solvents, hydrocarbons, hydrocarbon vapors, or other contami­nants.

Chapter 10 Retirement, Disposition, and Special Incident Procedure

  • The organization shall develop specific criteria for removal of PPE from service, including, but not limited to, issues that are specific to the organization, the manufacturer’s instructions, and the experience of the organization.
  • PPE that is worn or damaged to the extent that the organization deems it not possible or cost effective to repair the PPE shall be destroyed or disposed of in a manner that ensures the PPE will not be used in any firefighting or emer­gency activities, including training.
  • PPE that is contaminated to the extent that the organi­zation deems it not possible or cost effective to decontaminate the PPE shall be destroyed or disposed of in a manner that ensures the PPE will not be used in any firefighting or emer­gency activities, including training.
  • PPE that is no longer of use to the organization for emergency operations service shall be destroyed or disposed of in a manner that ensures it will not be used in any firefighting or emergency activities, including training.
  • PPE not in compliance with the edition of the NFPA standard that was current when the PPE was manufactured shall be destroyed or disposed of in a manner that ensures it will not be used in any firefighting or emergency activities, including training.
  • The chain saw leg protectors shall be retired when any physical damage results in the pulling out of cut-resistant fabric.
  • Special Incident Procedure.
  • The organization shall have procedures for the handling and custody of clothing and equipment directly rela­ted to serious firefighter injuries and firefighter fatalities.
  • In the absence of any other prevailing rules of evidence, the organization’s procedures shall include at least the following:
    • Provisions shall be in place for the immediate removal from service and preservation of all personal protective clothing and equipment utilized by the injured or deceased firefighter. Custody of such clothing and equip­ment shall be maintained at a secure location with controlled, documented access.
    • All such clothing and equipment shall be nondestruc- tively tagged and stored only in paper or cardboard containers to prevent further degradation or damage. Plastic or airtight containers shall not be used.
    • Personal protective clothing and equipment directly rela­ted to serious firefighter injuries and firefighter fatalities shall be reviewed by qualified members of the organiza­tion or by outside experts to determine the condition thereof.
  • The organization shall determine a specific period of time for retaining custody of the personal protective clothing and equipment.

Chapter 11 Verification

  • In order for an organization or ISP to he verified, it shall meet the requirements of this chapter.
  • Verification of the organization or ISP shall include inspection, cleaning, and repairs of garment elements only and shall not apply to helmets, gloves, footwear, chain saw protec­tors, or load-carrying equipment.
  • Where an organization or ISP is verified for conduct­ing repairs, the organization or ISP shall also be verified for cleaning and inspection.
  • The verified organization or ISP shall be listed.

11.1.1.3.1 The listing shall specify cleaning, inspection, and/or repairs that the organization or the ISP is verified to conduct.

  • All verification of the organization or ISP shall be performed by a certification organization that meets at least the requirements specified in Section 11.2 and that is accredi­ted for PPE in accordance with ISO/IEC 17065, Conformity assessment — Requirements for bodies certifying products, processes and services.

11.1.2.1 The accreditation shall be issued by an accreditation body operating in accordance with ISO 17011, Conformity assess­ment — General requirements for accreditation bodies accrediting conformity assessment bodies.

  • The verified organization or verified ISP shall not use the NFPA name or the name or identification of this standard in any statements about its services unless the services are veri­fied as compliant to this standard.

11.1.3.1 No provider of the services covered by this standard shall claim to be an ISP, a verified ISP, or a verified organiza­tion unless they comply with all the requirements in this stand­ard and are third-party verified in accordance with the requirements of this chapter.

  • Verification Program.

11.2.1* The certification organization shall not be owned or controlled by the organization or the ISP being verified.

  • The certification organization shall be primarily engaged in certification work and shall not have a monetary interest in the organization’s or ISP’s ultimate profitability.
  • The certification organization shall be accredited for PPE in accordance with ISO/IEC 17065, Conformity assessment — Requirements for bodies certifying products, processes and services.

11.2.3.1 The accreditation shall be issued by an accreditation body operating in accordance with ISO 17011, Conformity assess­ment — General requirements for accreditation bodies accrediting conformity assessment bodies.

  • The certification organization shall refuse to verify serv­ices to this standard that do not comply with all applicable requirements of this standard.

11.2.5* The contractual provisions between the certification organization and the organization or the ISP shall specify that verification is contingent on compliance with all applicable requirements of this standard.

11.2.6 The certification organization shall not offer or confer any conditional or temporary verification.

11.2.7* The certification organization shall have laboratory facilities and equipment available for conducting proper tests to determine organization or ISP compliance.

  • The certification organization’s laboratory facilities shall have a program in place and functioning for calibration of all instruments, and procedures shall be in use to ensure proper control of all testing.
  • The certification organization’s laboratory facilities shall follow good practice regarding the use of laboratory manuals, form data sheets, documented calibration and cali­bration routines, performance verification, proficiency testing, and staff qualification and training programs.
  • The certification organization shall require the organ­ization or ISP to establish and maintain a quality management program that meets the requirements of Section 11.4.
  • The certification organization and the organization or ISP shall evaluate any changes affecting function of the compli­ant services to determine continued certification to this stand­ard.

11.2.12* The certification organization shall have a follow-up inspection program of the organization’s or ISP’s facilities of the compliant services with at least one random and unan­nounced visit per 12-month period to verify continued compli­ance.

  • The certification organization shall be permitted to conduct specific testing to verify continued compliance.
  • The certification organization’s operating procedures shall provide a mechanism for the organization or the ISP to appeal decisions. The procedures shall include the presenta­tion of information from both sides of a controversy to a desig­nated appeals panel.
  • The certification organization shall be in a position to use legal means to protect the integrity of its name. The name shall be registered and legally defended.

11.3 Inspection and Testing.

  • For verification of the organization’s or ISP’s services, the certification organization shall conduct both inspection and testing as specified in this section.
  • All inspections, evaluations, conditioning, and testing for verification of the organization or ISP shall be conducted by a certification organization’s testing laboratory that is accredited in accordance with the requirements of ISO 17025,

General requirements for the competence of testing and calibration labo­ratories.

  • The certification organization’s testing laboratory’s scope of accreditation to ISO 17025, General requirements for the competence of testing and calibration laboratories, shall encompass testing of PPE.
  • The accreditation of a certification organization’s test­ing laboratory shall be issued by an accreditation body operat­ing in accordance with ISO 17011, Conformity assessment — General requirements for accreditation bodies accrediting conformity assessment bodies.
  • A certification organization shall he permitted to utilize conditioning and testing results conducted by an organization or an ISP for verification provided the organization or the ISP testing laboratory meets the requirements specified in 11.3.5.1 through 11.3.5.5.
  • Where an organization or an ISP provides condition­ing and testing results to the certification organization, the organization’s or ISP’s testing laboratory shall be accredited in accordance with the requirements of ISO 17025, General require­ments for the competence of testing and calibration laboratories.
  • The organization or ISP testing laboratory’s scope of accreditation to ISO 17025, General requirements for the competence of testing and calibration laboratories, shall encompass testing of PPE.
  • The accreditation of an organization’s or ISP’s testing laboratory shall be issued by an accreditation body operating in accordance with ISO 17011, Conformity assessment — General requirements for accreditation bodies accrediting conformity assessment bodies.
  • The certification organization shall also approve the organization’s or ISP’s testing laboratory.
  • The certification organization shall determine the level of supervision and witnessing of the conditioning and test­ing for verification conducted at the organization’s or ISP’s testing laboratory.
  • Sampling levels for testing and inspection shall be established by the certification organization and by the organi­zation or ISP to ensure reasonable and acceptable reliability at a reasonable and acceptable confidence level that repair serv­ices are compliant to this standard, unless such sampling levels are specified herein.
  • For verification of an organization’s or ISP’s cleaning services, the certification organization shall evaluate the organi­zation’s or ISP’s procedures in accordance with Section 7.2.

Tear Repairs.

required to be conducted using new materials as described in the table.

  • Initial samples submitted by the organization or ISP for verification shall be permitted to be prepared by that organ­ization or ISP.
  • For repairs to tears in the garment material the certif­ication organization shall inspect the tear in the material(s) to be repaired in accordance with Figure 11.3.8.2 and shall witness the repair of the samples to be tested.
  • The certification organization shall not allow test specimens that have been conditioned and tested for one method to be reconditioned and tested for another method unless specifically permitted in the test method.
  • The organization or ISP shall maintain all inspection and test data from the certification organization used in the verification of the organization’s or ISP’s services. The organi­zation or ISP shall provide such data, upon request, to the purchaser or authority havingjurisdiction.
  • Where an ISP or organization is verified for repair, the ISP or organization shall undergo verification on an annual basis.

11.4 Organization or ISP Quality Management Program.

  • The organization’s or ISP’s management shall define and document its policy and objectives for and commitment to quality and shall ensure that this policy is understood, imple­mented, and maintained at all levels in the organization or ISP
  • The organization or ISP shall operate an effective qual­ity system appropriate to the type, range, and volume of work performed.
  • The management of the organization or ISP shall desig­nate a person who, irrespective of other duties, shall have defined authority and responsibility for quality assurance within the organization or ISP The quality system shall be maintained relevant and current under the responsibility of the same person.
  • The quality system shall be fully documented. There shall be a Quality Manual, which shall contain at least the following information:
    • General information regarding the organization (names, addresses, phone numbers, and legal status)
    • Management statement on the organization’s or ISPs policy on, objectives for, and commitment to quality
    • Management statement assigning a responsible person for quality assurance
    • Description of the organization’s or ISP’s areas of activity and competence
    • Organization chart(s)
    • Relevant job descriptions
    • Policy statement on qualifications and training of personnel
    • Procedures for control of documents
    • Procedures for internal audits
    • Procedures for feedback and corrective action
    • Procedures for management review of the quality system
    • Distribution list for the Quality Manual
    • Work instructions or process manuals
    • Procedure for handling returns and complaints
  • The organization or ISP shall maintain a system for control of all documentation relating to its activities and shall ensure that the following occur:
    • The current revisions of the appropriate documentation are available at all relevant locations and to all relevant staff.
    • All amendments to documents are authorized and processed in a manner that ensures timely availability at the appropriate locations.
    • Superseded documents are removed from use through­out the organization, but one copy is filed for a deter­mined period.
    • Other parties, as necessary, are notified of changes.
  • The organization or ISP shall carry out a system of planned and documented internal quality audits to verify compliance with the criteria of this standard and the effective­ness of the quality system. The personnel performing the audits shall be suitably qualified for and independent of the functions being audited.
  • The organization or ISP shall have documented proce­dures for dealing with feedback and corrective action whenever discrepancies are detected in the quality system or in the performance of inspections.
  • The management of the organization or ISP shall review the quality system at least annually to ensure its continu­ing suitability and effectiveness. The results of such reviews shall be recorded.
NFPA 1877 Selection Care and Maintenance of Wildland Firefighting Protective Clothing and Equipment

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top